Leave a message

Тhank you!

We will contact you as soon as possible.

bg en sr ro gr uk ru

Hoses

Water Water hoses

Fuel Oil and fuel hoses

Ducting Ducting hoses

Air hoses Air hoses

Food and beverage hoses Food and beverage hoses

Acid and chemical hoses Acid and chemical hoses

Welding hoses Welding hoses

Hot water and steam hose Hot water and steam hoses

Automotive and boat hoses Automotive and boat hoses

Material handling hoses Material handling hoses

Cable protection hoses Cable protection hoses

Multipurpose hoses Multipurpose hoses

Stainless steel hoses Stainless steel hoses

Peristaltic pump hoses Peristaltic pump hoses

Criogenic hoses Criogenic hoses

PTFE hoses PTFE hoses

Garden hoses Garden hoses

Agricultural hoses Agricultural hoses

New hoses New hoses

 

Often searches

Discharge and suction hoses Discharge and suction hoses

Oil resistant hoses Oil resistant hoses

Abrasive resistant hoses Abrasive resistant hoses

Ventilation hoses Ventilation hoses

Gas hoses Gas hoses

 

 

News
SLM VAPOR HOSE
SLM VAPOR HOSE  Suitable for dispensers with active vapour recovery. Design and technical details see overleaf. Resistant to petrol and ozone, low diffusion.
SHANNON 85
SHANNON 85 Steel cord hose used for concrete placement at casting locations; it is used at the end of the pumps to distribute the concrete. The hose resists suction during the cleaning process. Usually supplied with swaged on “Full flow” hardened couplings.
MILKFLEX
MILKFLEX
Light and flexible lorry collecting hose suitable for milk and milk byproducts with an improved resistance to higher pressure.
Hose HYPERLINE V
Catalog
Hyperline V is designed for use in a wide variety of general purpose industrial applications, such as automotive, steam transfer, refrigeration, and many others. Although Hyperline V is also suitable for some light duty process fluid applications, Corroflon or Bioflex (both available from OPW market) is usually preferred due to the thicker PTFE wall and helical reinforcement. Hyperline V is very flexible and kink resistant, but has a convoluted bore which limits fluid flow rates, and reduces internal “cleanability”. It also requires de-convoluting before assembly. Hyperline FX is the preferred alternative which solves these problems without reducing the flexibility too much.
Hyperline V is available in the following grades
Hyperline V, TO - Natural PTFE Tube Only, no braid. Hyperline V, AS, - Antistatic Black PTFE Tube Only, no braid. Hyperline V, SS - Natural PTFE Tube, external 304 Stainless Steel Braid. Hyperline V, AS, SS - Antistatic PTFE Tube, external 304 Stainless Steel Braid. Hyperline V, PB - To special order, Hyperline V can also be supplied with an orange polypropylene yarn braid (Hyperline V, PB or Hyperline V, AS, PB). Hyperline V, AS, PB - Special order NOTE: Prolonged exposure to sunlight eventually results in UV degradation of PB braid. Seamless extruded and convoluted natural or antistatic PTFE tube, with a Stainless Steel 304 (SS) wire braid, or an orange Polypropylene Braid (to special order).

HYPERLINE V

• Automotive and General Industrial - where good flexibility is required for larger bore hose applications.
• Hyperline FX is preferred to Hyperline V in all applications except those where the superior flexibility and kink resistance of Hyperline V is required.

 

Temperature Rating
For Stainless Steel Braided (SS) hose, the temperature rating is from -70° to +260°C, but the Maximum Working Pressure (MWP) must be reduced by 1% for each 1°C above 130°C. For Polypropylene Braided (PB) hose, the maximum working pressure reduces by 5% for each °C above 80°C. Maximum Working Temperature = 100°C.
Pressure Resistance
The Pressure Ratings for SS grades are as listed and adjusted for temperature. Pressure ratings for PB hose grades are 50% of those for SS hose grades. Tube Only (TO) grades can only be used at pressures up to 2 Bar (30 psi).
Vacuum Resistance
SS braided Hyperline V hoses are fully vacuum resistant up to 130°C (266°F).
Flow Rates
Turbulent flow always occurs in hoses with rough or convoluted internal surfaces. This reduces flow rates, and can cause a whistling noise if gases are passed at high flow rates. Use Hyperline FX to solve such problems if necessary.

 

Assembly
Hyperline V can be assembled to hydraulic hose fittings in the normal way after the convolutions have been partially flattened out by means of a special tool, called a Visiflon Opening Tool, available from OPW market. This tool screws in to the convolutions, either manually or mounted on to an electric motor, and then screws out to leave the convolutions flatter, and able to accept the insertion of a hydraulic fitting.
HYPERLINE V

Number
DN Type I.D. O.D. wall R min WP BP Weight Length
inch   mm mm mm mm bar bar kg m
71-100-06-01-02 3/8” SS 6.30 11.94 0.63 20 60 240 0.13 40
71-110-06-01-02 AS,SS 6.30 11.94 0.63 20 60 240 0.13 40
71-100-08-01-02 1/2” SS 9.50 15.24 0.63 25 47 190 0.20 40
71-110-08-01-02 AS,SS 9.50 15.24 0.63 25 47 190 0.20 40
71-100-10-01-02 5/8” SS 12.70 21.21 0.76 40 40 160 0.25 30
71-110-10-01-02 AS,SS 12.70 21.21 0.76 40 40 160 0.25 30
71-100-12-01-02 3/4” SS 16.00 22.71 0.89 50 32 130 0.34 30
71-110-12-01-02 AS,SS 16.00 22.71 0.89 50 32 130 0.34 30
71-100-16-01-02 1” SS 22.20 30.58 1.00 63 26 105 0.47 25
71-110-16-01-02 AS,SS 22.20 30.58 1.00 63 26 105 0.47 25
71-100-20-01-02 1 ¼” SS 28.20 36.07 1.00 70 25 100 0.63 20
71-110-20-01-02 AS,SS 28.20 36.07 1.00 70 25 100 0.63 20
71-100-24-01-02 1 ½” SS 35.00 46.99 1.25 115 20 85 0.90 10
71-110-24-01-02 AS,SS 35.00 46.99 1.25 115 20 85 0.90 10
71-100-32-01-02 2” SS 47.00 61.01 1.25 130 15 70 1.25 10
71-110-32-01-02 AS,SS 47.00 61.01 1.25 130 15 70 1.25 10